Question 1

What does it do? can it make uno r3 connect to a router?

Accepted Answer

You can use it for linking n Uno r3 to connect to a router, or you can use it to replace that Uno r3 in some situations. As an example if you are using the Uno r3 to gather data from a temperature sensor, and if the temperature is below a certain point, toggle a relay to turn on a heater, you can do all of that with just this, and add in logging the temperature changes and information on whether the heater has been turned on to a web page. Or use it to sense light levels and turn on the front porch light and then turn it off again 6 hours later or at a time that it compares to an ntp server for. There are 4 GPIO pins on this, rx, tx, G0 and G2. The available libraries that support this device include i2c, the various 1wire devices, and so on. No you can't do SPI, so for now you probably won't be able to do datalogging to a flash card, but you can use the tx/rx pins to send such data to a Uno r3 where you can have SPI devices attached. Or as noted above log it to a server on the network w/o running it to a local flash card if you would like. If you do want to use it as a network bridge for an Uno r3, you will need to program it, and the Uno r3 to support the variation of hayes at+ command syntax, or program this to set up it's own connection and packetize the data coming from the Uno. There will be a learning curve in either case. But attaching an Uno to a wifi router is what it was originally sold to do. It's just a bit more capable than that.

Question 2

This is the only esp8266 chip that doesnt seem to support having new firmware flashed on it, anyone else have this problem? are these chips

Accepted Answer

You CAN flash the firmware on them, but to a hobbyist, it might seem like a miracle.  The trick is in pulling GPIO1 and 2, as well as the reset pin to the appropriate place.  Instructions on the internet are conflicting, and I can't honestly remember the setup I used, but I definitely did flash it with custom software from the Arduino IDE.Good luck!

Question 3

Spent 2 days following all instructions and tutorials.  send at command, no ok response from these type ii boards.  any lessons that actually work?

Accepted Answer

Maybe this can help you!
 Version II to test this module youtube tutorial: ★https://youtu.be/HDt8FS9t6lI; ★Version I youtube tutorial: ★https://www.youtube.com/watch?v=qU76yWHeQuw.
Link to view the technical details, ★https://nurdspace.nl/ESP8266; ★Introduction: https://github.com/sleemanj/ESP8266_Simple.

Question 4

How do i know the pins ? the pin coding on these chips are different from those online. what are the functions for pins -ce,csm,sck,mo,mi,iro? thanks!

Accepted Answer

Hi
These are ESP8266 ESP01 if you are looking at the opposite face of the pins with the antenna to your left you will have the following: on the left column top is RX ( 3.3V data level) one level down GPIO0 (general purpose Input/output 0) another level down GPIO2 (general purpose Input/Output 2) and bottom GND (ground).   On the right column top VCC (3.3V power line +) , one level down RST (reset = LOW active) another level down CH_PD (chip power down : LOW =power down active ) and bottom TX (3.3V data level).   I hope it helps

ASIN	B01EA3UJJ4
Best Sellers Rank	#1,375 in Serial Adapters #63,797 in Computer Cables & Interconnects
Brand	Makerfire
Built-In Media	4 * ESP8266 ESP-01S WiFi Serial Transceiver Module
Compatible Devices	Arduino
Connector Type	Micro USB
Customer Reviews	4.3 out of 5 stars 351 Reviews
Input Voltage	3.3 Volts
Item Dimensions	1 x 0.48 x 0.5 inches
Item Weight	0.02 Pounds
Item dimensions L x W x H	1 x 0.48 x 0.5 inches
Manufacturer	MakerFocus
Mfr Part Number	ES3143916Z64RB378
Model Number	Esp-01
Number of Items	4
Number of Ports	5
Package Quantity	1
Power Plug Type	No Plug
UPC	190033500186
Unit Count	4 Count

Makerfocus 4pcs ESP8266 Esp-01 Serial Wireless Wifi Transceiver Module Compatible with Arduino

Details

Details

Description

Specifications

Reviews

Common Questions