Weatherproof ABS Solar Double Cable Entry Gland

My solar project is on a 16’ cargo conversion. I installed two panels on the roof. I needed this gland in order to make solar cable intry to the utility space i have under a cabinet. This gland has held up nicely after a year. I do recommend placing a small screw in both the front and rear of this gland to help secure to the metal roof. On warm days the gland wanted to lift up after the RV roof sealer got hot. The two small stainlesss screws did the job. I do recommend this gland if you are adding solar panels on your RV or conversion project.

Fast and no issues

Great product easy to install

Item physically is great. Feels durable and should have zero issues doing as designed. However I ordered "White" and received the item in an Almond color (like the light switches/covers found in your home). Happy with the product but color is wrong and would stand out. I'll be exchanging it for the black version as that'll at least look less awkward on the roof.

Worked great on the roof of my RV. Half the size of the OEM one installed on the other side. Was able to fit 8awg wire through the connectors without issue. Started installation by removing a recessed light in the bedroom that was 8 inches from a wall. Lights just release and hang; they are held in with 2 spring clips. Reached in with my hand and felt a plastic vent pipe going to through the wall to the roof. Went on the roof and drilled a 1/2 inch hole down through the roof and through the 2x2 stud going across the wall. Ran 2 8awg wires down and pulled them out through a small hole I made in the wall under the sink. Ended up ripping the whole thing apart and made the hole 1 1/4 inch to be able to use this wall as a chase. Unit installed on the roof with butyl tape and Dicor. Fastened it with 4 screws. Looks great.

Used this to run antenna cables into a shed. Good quality part. Has kept water tight for almost 1 year

Easy to install. When using it to go through metal, trim the metal so it doesn't come in contact with your wires, or have the metal a 16th of an inch bigger than the opening. Low profile and has an angle area, if using on a vehicle or towed vehicle, place it so the angled part towards the front.

This is actually on the outside of my workshop for building computers (ie, wood siding). It's not painted or primed, so if it's exposed it must be painted. UV breaks down plastic, not heat, so PAINT it. I've converted entirely to solar and am running the 10 ga. wire through this from the panels to the battery...and they fit like a glove when the nuts are tightened even slightly. This thing works very well, seals tight, and is well made. A little caulking all the way around on the flange that butts to the surface of the wood, a coat of paint the next day and it's as watertight as it can be. The nuts are a little close together, so you may need a wrench to tighten them if you have bigger fingers..not a lot of room to work right there. I'd use silicone on a smooth surface, boat or RV, but keep in mind silicone is NOT paintable unless it's labeled so (silicone/acrylic).

Good item arrived in time. Used this to bring two WiFi co ax through the roof of Motorhome. Works fine. Did drill some holes around the flange and glued and screwed to the roof. WiFi coax are very small to able to pass the connectors through the gland and then fit the unit to roof. Just fits under the antenna stand off bracket as well.

I bought it a couple of years ago and it is still going well. Not leaking and everything still looks good

Ok does the job

Just what I needed

Fitted this to the roof of my motorhome to run 2 cables into the van. Easy to assemble and fit. The cable entry glands don't close down as much as I wanted, but they seem to seal well, especially after applying sealing goo on everything. You can't take any chances when you drill into a motorhome roof! Overall, I was pleased with this, it looks good and everything fits well.