PVC Stitch Liquid Patch

This stuff is awesome!! Worked perfect in my son’s inflatable bounce house that had a tear, and has been holding for days not and he’s not gentle! Glad I have this for any other holes that may appear.

Great PVC glue to fix boats and rafts. This glue fixed my inflatable paddleboard that needs 15 psi. I globbed some glue on it and let it sit overnight even though it says it can cure in a few hours. The leak was a small 1cm crack thay was a slow leak, not a full slice into the side. Blew it up to 10+psi and no leak! The repair seem flexible and hopefully will hold up. I also used it to repair an inflatable raft that only needs 1 psi. Im sure it will work on the low pressure raft but I havent inflated that one yet. The previous sticky patch I tried on the hole didn't hold so it needed this stronger flexible PVC glue. It was also about a 1cm long hole in the raft. Im keeping it in the freezer to keep it supple so I can use it again. But for the price, it's worth even just one fix and I already got two out it. Great value fir the money. I included a pic to see the crack versus the size of the tube of glue.

works great, as described

This works perfectly for sealing holes. I used it on a Coleman air mattress I bought used. It had 2 puncture marks on the top and a matching set on the bottom. Multiple layers of duct tape didn’t work, so I tried this. Because the holes were on both sides, I had to do them one side at a time. It is easy to apply and took only a few hours to dry, so I was able to complete both sides in a day. I inflated the mattress and even had my adult son (about 200 pounds )hang out on it for a while watching tv. No leaks. I left it aired up for 3-4 days and my dogs jumped on it and slept on it, still no leaks. I think it’s ready for our next camping trip. Some have said that it dried up after the first use, and I have noticed that the cap isn’t completely secure, so I put a small square of tin foil on the top before screwing the lid on. Hopefully that will help, but I guess we’ll see.

This might seem expensive but compare it to the cost of a new air mattress at $100 - $150 for anything decent (internal pump and made of PVC, not vinyl). I had to repair a spot where the seam separated. I had left it a tent pumped up pretty firm and the day got up into the 80s. It still probably would have been fine if I hadn't off taken a nap on it not letting some air out first. Operator error. It can be seen in the photo, about 1/4" in length. I had previously tried another product which used an adhesive and patches. This did not work for 2 reasons. It was a seam but more importantly when the air mattress is pumped up it stretches. This will pop the patch loose because they don't stretch the same. I tried putting successively larger patches (2) over the original patch. It held for one night but only because I used a heat gun to carefully heat up the patches and mattress while it was pumped up. The varying stretch though made the patch start leaking again. It was remarkably easy to peel the patches off to use PVC Stitch so they were never really well attached. I spoke with the owner of the company and did the following on his advice (love small companies. He had tested this product himself on various items including a BC bladder to more than 3 atmospheres. That's quite a bit more pressure than any air mattress will be under). I cleaned the area with 90% isopropyl alcohol (air was out but not sucked completely flat using the pump). I set up the mattress so the split in the seam was at the bottom of a shallow indentation. This was the hardest part because the mattress kept shifting. I used some light weights to hold it in place. I opened the tube of PVC Stitch and squeezed out enough so the seal would extend 1/2" on all sides of the split, and let it dry. Don't spread it out just let it flow out by itself. It will spread a little and flatten out by itself. As a note, I had asked how long the tube would last once open and was told to close out back up immediately. Do not let the tube sit open. It is about 80% solvent which is how it melts the surface of the object you're trying to repair do that the PVC Stitch is unitized with PVC or vinyl to trying to repair. I made the repair at about 65° F with under 50% humidity. I waited 24 hours to pump it up again but I was assured that it would be usable in about 2 hours (dependent on temp and humidity. Affects how rapidly the solvents evaporate). When you can no longer smell the solvents in the repair area is good to go. My air mattress is PVC which is the strongest type made and stretches the least (although they still stretch a little). I used it last night and it didn't leak a bit of air. This product saved me a lot of money, not to mention the fact that this air mattress is no longer available. Since this split when I was camping I had to go out and buy a replacement. The replacement leaks from the inflation, deflation port which apparently is a very common problem with this design. There is no way to fix that. The result is that a supposedly normally functioning air mattress has to be pumped up 2-4 times a night. My repaired air mattress is working flawlessly thanks to PVC Stitch. Thankfully I didn't throw it out even after the first attempt to fix it failed.

This stuff seems to work great. I had some deep scratches in my iSUP that were down to the fabric. I did not have an air leak, but wanted something to cover the scratch and provide protection. Perhaps a patch would have been more durable, but this product is very easy to use and covered the scratch in a flexible layer of new PVC. I didn't test the repair to see how durable it is, but it seems robust. For my application I laid it on thick. I applied a bead of the "glue" and left it. I did not smooth it out and when it cured I had a nice thick coat of new PVC material filling in the scratch.

Didn’t work !! When used for the first time seems like is only air inside the tube. I tried 3 different times but didn’t work. I fallowed the instructions and nothing. I am really sad because is not cheap product!!

Bought this to repair 2 airbeds that had small leaks on the seams--the first hole was about 1/8" and the other was about 1/4". Followed the directions--clean area, apply glue, let sit for 24 hours. Used the airbed with the larger leak, and it began leaking again the first night. Switched it out for the airbed with the smaller leak and it was fine for the 1st and 2nd night, it began leaking again on the 3rd night. Not really worth the money if the repairs only last a day or two.

رائع بصراحة ، وهو سائل كثيراً لذلك لابد أن تضعه على شكل طبقات متفرقة في الوقت ، بمعنى كل ساعتين تضع كمية خفيفة وهكذا عدة مرات حتى تتشكل رقعة صلبة، لانك لو وضعت كمية كبيرة مرة واحدة فسوف تنسكب المادة لانها سائلة جدا، لذا فإن وضعها بكميات بسيطة بشكل متكرر هو ما يضمن تشكل رقعة متينة وقوية

So far it’s work, no complaints about it

Todo muy bien

Used this product to repair a number of air leaks in my ageing Stand Up Paddle Board that were unable to be repaired with patches. So far, the repairs seem to be holding up which is a big result as otherwise, the SUP was destined for the tip!

ممتاز جدا جربته على مرقد الهواء ثابت وغطى القطع بس لازم تتبعون التعليمات بالضبط علشان يكون نتيجته ثابته