Omoton [4 pack] Samsung Galaxy Note 20 Ultra Screen Protector - TPU Film Screen Protector for Galaxy Note 20 Ultra 6.9 Inch, 2020 [High Definition] [Bubble Free] [Anti-scratch] [Anti-Fingerprint]

Easy apply, durable.

Good but didn't fit my case

Very easy to apply with no bubbles the 1st and only attempt! Followed included, clear instructions word for word. It worked!

I'm using this on a Samsung Galaxy Note 20 Ultra 5g. Although it's a nice phone Samsung could not have made it harder to protect if they had tried. The screen is huge and extremely curved at the edges. The fingerprint sensor is located on the screen and is quite finicky. The rear camera module is huge and protrudes so much that the phone wobbles when it's on its back. Although it appears that Samsung has a factory screen protector on the phone when you buy it in some countries that's not the case in the US - it comes without a protector. I would have rather had a tempered glass protector, but every single one even the very expensive ones had reviews complaining about the fingerprint sensor no longer working and problems adhereing to the curved edges, so my only option was a TPU protector and I went with this one because the price was right and all the install accessories it came with. I've always had terrible luck applying TPU screen protectors, but I watched the video they direct you to and followed the directions. The result is that for the first time in my life I have a screen protector that is perfectly aligned and looks great - and since there are 4 to a pack I have 3 more left in case it wears out or gets damaged. Here are some hints based on my experience: (1) Watch the video - this is easy to do, but it's a multi-step process and you have to follow the order of steps. (2) The black foam piece that you place the phone against is needed for a good install, BUT be careful where you place it. The glue on the foam piece is a bear to get off when you remove the piece, so make sure you don't destroy an expensive piece of furniture. The foam is also not quite high enough for the Ultra AND the Ultra itself doesn't lie flat on a table surface because of the camera module. I solved that by placing a soft micro fiber under the phone so that it wasn't wobbling. (3) When they say to press hard they're not kidding. Also at least on the one I used the green edges never just came up from the pressure, I had to reach in and get them started. (4) When I was done the alignment was great, but there was a line of small bubbles in the middle which I couldn't get out no matter how hard I tried to push them to the edge. I was not a happy camper, but after about 7 hours they just went away by themselves, so there's no bubbles on it at all. The fingerprint sensor works as well as it always did (I increased the touch sensitivity but it really isn't necessary to do that), and the display looks about as bright as it did before, and the feel when using the S-Pen is about the same as before. I don't think TPU screen protectors protect as much as tempered glass ones do, but until if and when they make a protector that works well with the Ultra this will keep the screen from being scratched, looks great and the price was really low. I don't know how long it will last (I've only had it a day), but since you get 4 in the pack and the price is so low I'm set for a long time.

First off, the screen protectors I received are most definitely not a matte finish, they are glossy. That said, they're no more reflective outdoors than the naked screen or a tempered glass screen protector. I found the installation to be a breeze, and the product went on without a hitch. The installation system on this is really well thought-out. Props, too, to the reviewer who suggested using a towel as a pad to keep the phone from wobbling, that's what I did and it really helps. HOWEVER, I'm one of those people who rtfm and watch the installation video not once but twice (once to get familiar, and a second time with all the tools and materials in front of me to do a mock run-through on the installation). As a result, one perfect installation, total elapsed time, 10 minutes max, probably closer to 8. OTOH, there's my kid, digital native, has the same phone, but hasn't (yet) learned the importance of pre-flighting tasks. He read the little instruction booklet and went immediately to work. First one had a bubble. Second one, I have NO idea how it got so messed up, but it did. Third one (and last of the four-pack, remember, I used one) went on but had a few bubbles. Total elapsed time: 20+ minutes, plus a bunch of wasted plastic. I call installer error on his experience, lol. He'll learn. Bottom line: READ THE INSTRUCTIONS. WATCH THE VIDEO. DO A DRY RUN FIRST. WORK SLOW. This ain't something that requires a college degree, but don't go thinking that bc you're smart you already know how to do it right. The screen protector itself is fine, a typical tpu protector. I'll probably eventually replace it with tempered glass (now that I have no spares, lol) because I work on construction sites or out in the wilderness, so impact and grit resistance are important. This screen protector will get me through until I find a non-glare tempered glass one.

Compatible with my phone, Good quality and thick enough Fits perfect and is worth the cost