LEDMO Dimmable LED Driver 12V DC 60W Quiet Operation Universal Regulated 12V Transformer Input/Output Isolation Protection LED Power Supply for Christmas Strip Light

Great Quality & Value- works fine

I had an old 30W driver running some LED lamps but I wanted to add more lighting but it would exceed the capacity. I have the driver connected to an Eaton dimming smart switch. After reading the reviews I decided to buy this driver. When it arrived It was well packaged and came with a small "instruction manual". I wouldn't necessarily would call it an instruction manual because its mostly warnings and what the driver features are. If you need instructions on how to correctly wire this please for yours and everyone else safety, hire a professional. Pretty straight forward High voltage on one side, low voltage on the other (observe correct polarity). The only issue I had which seems consistent in the reviews is removing the covers to access the terminals and mounting holes. I installed mine indoors so I cannot comment on its weather resistance but looking at the design it would need protection if you mounted it outside. When the driver is powered there is a green LED that illuminates. I have 5 - 12V 7W LED MR16 lamps connected to the driver (35W total). The dimming is very smooth and effective through the entire range with no flickering or stepping. The dimmer I'm using is an Eaton RF9540-NAW ASPIRE Single-Pole Multi-Location Master Dimmer Light Switch.

working well so far, dimming is good, will see how long it will last. The caps on both ends are so difficult to remove, why? hence 4 star

I had a large heavy halogen 24 volt transformer that caused the replacement LED bulbs in my track lights to "sing". This stopped it, and increased the range of the fader. It's small, and easy to install even without any instructions other than the diagram on the top of the unit. If you can't figure it out from that, you probably shouldn't be installing it yourself! The only gripe I have is getting the end covers off. (orange parts) They have no release and you need to use a screwdriver to pry them up to get them off. The nice feature of them is they ratchet down on the wires to hold them in place once the install is complete. Also mount it before you wire it. Otherwise the wires cover the mounting holes.

Updated: Go figure less than a month after writing a review, I’d have to come back and change it. I had a customer try this on a setup that’s full compatible and both drivers they ordered had issues. Sad to say I’ll have to switch brands after spending hours dealing with that. Original: I’ve bought 4 of these now, one being over 4 years in constant use. They dim well, minimal noise and hold up to the test of time. So far, these are my favorite dimmable drivers.

I just now installed this for some LED strips.. not sure if I exceeded the capacity of this or not.. I do not have it connected to a dimmer, however. It's not "instant on" but it does have a soft start-up that is quick enough. In fact, it gives a very elegant effect when you activate your LEDs with this. Since I literally just now installed it, I do not know what the longevity of the unit is. If anything I hope it outlasts the last drivers I bought. In regard to the covers on each end, i didn't have a problem removing it. I just used a flat head screwdriver to carefully pry them, up by inserting the end and turning the screwdriver side to side. the covers are a good way to secure and shield the wiring.

Didn't last any more than 2 months. Customer service sent me out of replacement right away but I still had to go and install it for free on my time. for a little bit more money you can get a driver of quality that will last you years and years

Easy to install, low noise, worked fine until today. Purchased in October 2022, installed driving some small LED undercabinet lights way less than the 60 w rating of the power supply. Today it died, slight smell of electronic component failure in the air. Power to the unit is good. Checked lights with 12 volt battery and they are good. Bench tested, power supply not good. So how does the 5 year warranty as listed in the advertisement work? No contact info to find out. Inquiring mind would like to know.

Have had no issues with this transformer. I purchased it to control some LED lighting that I install in one of our bathrooms. It's mounted in the attic and has survived -28 degree Celsius this winter. So far so good.

Works great. Easy to use but the end caps are a little difficult to remove. Once they’re back in place they hold the wires fast and the design allows for a lower profile installation although it is slightly larger than others I’ve used. Good product tho. Will purchase again.

I purchased this dimmable led driver when the transformer in the base of my halogen floor lamp failed and I couldn't find a replacement transformer small enough to fit in the base. Then once I decided to go with an external transformer, I decided to "future proof" my floor lamp by having a system that could eventually be upgraded to LED. For now I'm sticking with a halogen bulb, however I was hesitant to purchase this unit, as it does NOT explicitly say in the product description that it will drive a halogen bulb, although there is a picture showing a "Tungsten" fixture. My final configuration is Lutron Caseta plug in lamp dimmer to a 2 wire power cord wired to the LED Driver/transformer, then another power cord wired on the secondary side, then 35W GY6.35 halogen capsule bulb. NOTE: I had looked all over amazon.ca for a GY6.35 dimmable warm white 12V LED replacement, but could not find anything. If I find one in the future, I will simply swap out halogen for LED. With the halogen bulb, there is no flicker when dimmed and I am using a 35W halogen lamp with this 60W LED driver. Some tips 1) Removing the orange plastic wire covers; there is no clear instruction on how to do this. Check out my marked up photograph. I used a standard cutlery knife (screw driver was too thick) and inserted it where the red arrow is on my photo.....first one side, insert and bend the knife sideways a bit to loosen the bond between the rides on the clamp and main body, then try to pull that whole side up. Do the same on the other side. Once you get the orange piece out you'll see there are a series of raised ribs that click,click,clikc ratchet the clamp down and keep it tight on your attached external wiring. 2) The screw terminals that tighten down on your external wires; the bottom part of these terminals that tighten onto your wires, the size is quite small, so it's easy to think you get a good connection and you could be only compressing a few strands of wire. Make sure your stripped wire is nicely twisted and as you tighten the terminal, watch the wire being compressed to make sure it's in the middle of the compression screw. 3) Although the line input has an indicator for a GROUND lug, my Lutron Caseta plug in wall dimmer does not have a ground lug (only neutral and line), to I only used a 2 wire extension plug with neutral and line. No problem doing it this way. Everything works. 4) On the top of the LED driver, the specs are listed. Although the AMPS are listed, the maximum wattage is not listed. I added a "P-Touch" label on the top of the unit stating MAXIMUM 50W - for this 60W unit. ***EDIT*** When used with a Lutron Caseta dimmer there is a slight high frequency buzz between 20% and 80% intensity (35W halogen) I don't think this would be noticeable at all if the LED driver was located in a cabinet. Unfortunately I have the unit on the floor next to a chair, so I can hear the buzzing. For now I may try a lower wattage bulb at 100% dimmer power

works as advertised

Just installed today. Works as expected, but not on a dimmer yet. Rating is based om the ease of install. Orange wire clamps are dam near impossible to remove. Instructions are pathetic. They tell you to use a screwdriver to remove the clamp... biy not who. They could take a page out of ikea's playbook.